Message erreur

Program Version,EnergyPlusDLL-OMP-32 7.2.0.006, 26/04/2013 08:54,IDD_Version 7.2.0.006
** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.
************* Beginning Zone Sizing Calculations
** Warning ** Site:GroundTemperature:BuildingSurface: Some values fall outside the range of 15-25C.
** ~~~ ** These values may be inappropriate. Please consult the Input Output Reference for more details.
** Warning ** Detached shading effects are ignored when Solar Distribution = MinimalShadowing
** Warning ** GetSurfaceData: Construction 11 of interzone surface RDCBAS:HALLD%ACUEIL_PARTITION_4_0_0 does not have the same materials in the reverse order as the construction 12 of adjacent surface RDCBAS:SANITAIRES_PARTITION_5_0_10039
** ~~~ ** ...but Nominal U values are similar, diff=[0.0000] ... simulation proceeds.
** ~~~ ** ...if the two zones are expected to have significantly different temperatures, the proper "reverse" construction should be created.
** ~~~ ** ...this problem for this pair will not be reported again.
************* Note that the following warning(s) may/will occur if you have not enclosed your zone completely.
** Warning ** Entered Zone Volumes differ from calculated zone volume(s).
** ~~~ ** ...use Output:Diagnostics,DisplayExtraWarnings; to show more details on individual zones.
** Warning ** CheckUsedConstructions: There are 10 nominally unused constructions in input.
** ~~~ ** For explicit details on each unused construction, use Output:Diagnostics,DisplayExtraWarnings;
** Severe ** DayltgAveInteriorReflectance: Multiplier > 1.0 for window RDCHAUT:HALLD%ACUEIL_WALL_3_0_0_0_0_0_WIN in Zone=RDCHAUT:HALLD%ACUEIL
** ~~~ ** ...an adjacent Zone has daylighting. Simulation cannot proceed.
** Fatal ** Progrem terminates due to preceding conditions.
...Summary of Errors that led to program termination:
..... Reference severe error count=1
..... Last severe error=DayltgAveInteriorReflectance: Multiplier > 1.0 for window RDCHAUT:HALLD%ACUEIL_WALL_3_0_0_0_0_0_WIN in Zone=RDCHAUT:HALLD%ACUEIL
************* Warning: Node connection errors not checked - most system input has not been read (see previous warning).
************* Fatal error -- final processing. Program exited before simulations began. See previous error messages.
*************
************* ===== Final Error Summary =====
************* The following error categories occurred. Consider correcting or noting.
************* Nominally Unused Constructions
************* ..The nominally unused constructions warning is provided to alert you to potential conditions that can cause
************* ..extra time during simulation. Each construction is calculated by the algorithm indicated in the HeatBalanceAlgorithm
************* ..object. You may remove the constructions indicated (when you use the DisplayExtraWarnings option).
*************
************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors.
************* EnergyPlus Sizing Error Summary. During Sizing: 5 Warning; 1 Severe Errors.
************* EnergyPlus Terminated--Fatal Error Detected. 6 Warning; 1 Severe Errors; Elapsed Time=00hr 00min 23.13sec

Que signifie ce message d'erreur ?

Bonjour,

Les messages d'erreur anglais viennent du moteur de calcul E+. Il faut repérer les messages précédés du mot SEVERE. Dans votre cas :
Ici, dans le Hall d'accueil RDC Haut vous avez certainement plusieurs fenêtres de même taille qui ont été envoyé à E+ comme une seul avec un multiplicateur. DesignBuilder le fait pour réduire les temps de calcul et seulement si vous laisser cocher l'option Consolider les fenêtres similaires qui se trouve dans les Options de Modélisation, onglet Avancé.

E+ veut calculer la luminosité de la zone et n'accepte pas que les fenêtres soient fusionnées, je pense qu'en décochant l'option de Consolidation de DB vous pourrez lancer la simulation.

Cordiales salutations,

Merci, problème résolu.